Some of the things that determine air conditioning capacity in Arizona include, but are not limited to: your area’s unique climate, monsoon humidity, number of windows, their location, and their NFRC rating, ceiling and wall insulation factors, which direction your home is facing, how much heat your appliances produce, how high your ceilings are, if you have a basement, if you have proper attic ventilation, the location of trees on your property, and even the number of people who occupy the home.
Your HVAC professional can also help you verify that your system is properly matched by providing you with an AHRI Certificate of Certified Product Performance upon request. The certificate verifies that the outdoor unit (condenser) and the indoor unit (evaporator) combination has been certified as a matched system by the Air Conditioning, Heating and Refrigeration Institute (AHRI). For higher efficiency systems, this certification may help you obtain a rebate from your utility or local municipality if you have to replace your unit in whole or in part. Not all areas offer a rebate, but your technician will likely be able to provide information about the certification process. Fees for performing this certification vary, but generally are relatively inexpensive.
Vredevoogd Heating & Cooling Grand Rapids values each and every customer. Servicing or installing your HVAC system means establishing a service relationship with each homeowner. We promise to earn your trust with our consummate level of professionalism and expert service. We back our work with the strongest industry guarantees because we value your continued business.

I have a very old HVAC. The heater went out. I had just purchased the heater check package from Angie's list and it went out the nex tday. I called them and John came within a day or so. He found the problem after checking several items (fuse in heater shorting). He ordered the part and there was a delay due to getting the part and then the ice storm. As soon as the part was in John texted me. When I was available, John came back in a reasonable time and fixed it. He always called half hour before he was en route to notify me and was very punctual. He is professional and knowledgeable. He used my coupon toward my total bill and I have heat! I will use him again and am thankful he could get out and get it fixed at a reasonable cost.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
Get an accurate price for your HVAC repair costs by contacting a local heating and cooling company and scheduling an inspection. Search HVAC.com’s Contractor Directory to find local HVAC contractors who perform heating and cooling repairs. Call for service and find the price of the HVAC repair costs needed to get your system back into good working order!
Trying to replace an HVAC unit when out of town isn't easy, but Gator Air made it seamless. I was able to quickly schedule the estimator to come to my property and I was emailed several options. I was never pushed to make a decision or "sold" unwanted options. The installers were punctual and professional. Outstanding follow up too. I highly recommend!
HVAC repair technicians are properly qualified to take care of anything that relates to installing, maintaining or repairing your heating, air conditioning and refrigeration systems. Our professionals have gone through rigorous training and certification and all our technicians and equipment installers are NATE-certified, which involves demanding testing and indicates a solid understanding of the industry.
Air conditioning (often referred to as AC, A/C, or air con)[1] is the process of removing heat and moisture from the interior of an occupied space, to improve the comfort of occupants. Air conditioning can be used in both domestic and commercial environments. This process is most commonly used to achieve a more comfortable interior environment, typically for humans and other animals; however, air conditioning is also used to cool/dehumidify rooms filled with heat-producing electronic devices, such as computer servers, power amplifiers, and even to display and store some delicate products, such as artwork.
Its unique feature is the presence of one main external unit that connected to several indoor units. Such systems might be the right solution for maintaining the microclimate in several offices, shops, large living spaces. Just few of outdoor units do not worsen the aesthetic appearance of the building.The main external unit can be connected to several different indoor types: floor, ceiling, cassette, etc.
For residential homes, some countries set minimum requirements for energy efficiency. In the United States, the efficiency of air conditioners is often (but not always) rated by the seasonal energy efficiency ratio (SEER). The higher the SEER rating, the more energy efficient is the air conditioner. The SEER rating is the BTU of cooling output during its normal annual usage divided by the total electric energy input in watt hours (W·h) during the same period.[33]
An example of a geothermal heat pump that uses a body of water as the heat sink, is the system used by the Trump International Hotel and Tower in Chicago, Illinois. This building is situated on the Chicago River, and uses cold river water by pumping it into a recirculating cooling system, where heat exchangers transfer heat from the building into the water, and then the now-warmed water is pumped back into the Chicago River.[25]
The most recognized standards for HVAC design are based on ASHRAE data. The most general of four volumes of the ASHRAE Handbook is Fundamentals; it includes heating and cooling calculations. Each volume of the ASHRAE Handbook is updated every four years. The design professional must consult ASHRAE data for the standards of design and care as the typical building codes provide little to no information on HVAC design practices; codes such as the UMC and IMC do include much detail on installation requirements, however. Other useful reference materials include items from SMACNA, ACGIH, and technical trade journals.
The concrete pads under home air conditioner and heat exchanger units tend to settle over the years. As long as there’s no strain on the copper coolant tubes and electrical lines, and the unit stays dry and level, it’s OK that the pad has sunk. But if it continues to sink and pulls the lines tight, or if water puddles around the unit, you’ll need to take action. Here’s how to fix it.
Even with the best air conditioning repair service Phoenix can offer, an AC unit that has reached the end of its shelf life must be replaced. If you are ready to upgrade or replace that aging system, call us now for a free estimate, or check out our AC Unit Replacement section. In addition to offering our own Precision Line with the best warranty available in the industry, we also partner with industry leaders to offer the highest quality equipment at the best possible price, and we personally stand behind all of our new equipment installations.

The blower assembly is located between your main furnace and the cold air return. The blower is responsible for pulling air from your home and then sending it through the furnace and the heat exchanger. The air gets circulated throughout the home via the duct work. The furnace’s air filter is contained within the blower compartment. Regular-style filters should be replaced or cleaned each month.

Air flow meter Aquastat BACnet Blower door Building automation Carbon dioxide sensor Clean Air Delivery Rate (CADR) Gas sensor Home energy monitor Humidistat HVAC control system Intelligent buildings LonWorks Minimum efficiency reporting value (MERV) OpenTherm Programmable communicating thermostat Programmable thermostat Psychrometrics Room temperature Smart thermostat Thermostat Thermostatic radiator valve


If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
×