Family owned and operated, Kabran Air Conditioning & Heating continues a tradition of excellence begun in 1984.  We expertly solve any heating or cooling challenges in the Space Coast area, from commercial or residential installation, retrofit, upgrade, maintenance, or repair.  Whether the job is big or small, a carefully considered project or sudden emergency, we provide prompt response, personalized attention, and informed recommendations.  Keeping your exact circumstances and requirements in mind, we protect your ongoing satisfaction with accurate workmanship and the highest quality products.  For skilled heating and air conditioning service at reasonable rates throughout Cocoa Beach FL, Satellite Beach FL, Cape Canaveral FL, Rockledge FL, Melbourne FL, Merritt Island FL, Viera FL, Indian Harbour Beach FL, Kabran Air Conditioning & Heating is the name you can trust.
Heaters exist for various types of fuel, including solid fuels, liquids, and gases. Another type of heat source is electricity, normally heating ribbons composed of high resistance wire (see Nichrome). This principle is also used for baseboard heaters and portable heaters. Electrical heaters are often used as backup or supplemental heat for heat pump systems.

Our team of fully licensed and insured technicians each draw from between ten and thirty years of industry experience and share our unwavering dedication to customer service.  Entirely NATE-certified, our installation and service department has completed rigorous testing, and are exceptionally qualified to handle even the most complex HVAC challenges.  NATE (North American Technician Excellence) is the only nationwide certification program that is supported by the entire industry, and of all third-party certifications, has the lowest pass rate.
The concrete pads under home air conditioner and heat exchanger units tend to settle over the years. As long as there’s no strain on the copper coolant tubes and electrical lines, and the unit stays dry and level, it’s OK that the pad has sunk. But if it continues to sink and pulls the lines tight, or if water puddles around the unit, you’ll need to take action. Here’s how to fix it.
We understand having problems with your air conditioning system - can be frustrating and uncomfortable. That's why Gator Air Conditioning only employs background checked, drug tested, highly trained and certified technicians. And we are so confident in their skill to correctly diagnosis and complete your Air Conditioner repair that we cover them with our Fixed Right Guarantee. Our Comfort Advisors come from the industry with the technical expertise needed to ensure the air conditioning systems we quote will be sized right to maximize performance. We employ the best air conditioner installers in Bradenton, FL to ensure your air conditioning system will be installed right to meet or exceed manufacturer recommendations. For your peace of mind, our Installation Guarantees cover more than just the equipment… we also cover your money, time, our workmanship, and your satisfaction.

Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.


An air conditioning system, or a standalone air conditioner, provides cooling and humidity control for all or part of a building. Air conditioned buildings often have sealed windows, because open windows would work against the system intended to maintain constant indoor air conditions. Outside, fresh air is generally drawn into the system by a vent into the indoor heat exchanger section, creating positive air pressure. The percentage of return air made up of fresh air can usually be manipulated by adjusting the opening of this vent. Typical fresh air intake is about 10%.


Air conditioning and refrigeration are provided through the removal of heat. Heat can be removed through radiation, convection, or conduction. Refrigeration conduction media such as water, air, ice, and chemicals are referred to as refrigerants. A refrigerant is employed either in a heat pump system in which a compressor is used to drive thermodynamic refrigeration cycle, or in a free cooling system which uses pumps to circulate a cool refrigerant (typically water or a glycol mix).
Before calling to schedule your appointment, it may be helpful to familiarize yourself with the air conditioning equipment that you have. Make sure you know at least the brand name, the model and the approximate age of the system, as well as any warranties that may be in effect—and read through our AC FAQ to see if any of your symptoms sound familiar.

Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
Coolray & Mr. Plumber have Smyrna, GA covered when it comes to air conditioning repair and installation, furnace repair and installation, plumbing service and more. We also offer a full range of HVAC and plumbing products to help meet the needs of Smyrna homeowners and businesses. We have been serving Smyrna, GA residents since 1966 and our HVAC technicians and plumbers have the experience and training to properly resolve all of your heating, cooling and plumbing issues. Our products include furnaces, air conditioners, heat pumps, geothermal HVAC systems, traditional water heaters, tankless water heaters, sump pumps, air cleaners & air purifiers and more. 
The concrete pads under home air conditioner and heat exchanger units tend to settle over the years. As long as there’s no strain on the copper coolant tubes and electrical lines, and the unit stays dry and level, it’s OK that the pad has sunk. But if it continues to sink and pulls the lines tight, or if water puddles around the unit, you’ll need to take action. Here’s how to fix it.
On average, furnace repair costs $287 nationally, with some homeowners spending as little as $60 while others paying $900 for furnace maintenance. Repairs to an electric furnace can run you $300 or less, while gas furnace repairs can be more complex and range from $375 to $1,200, depending on the what needs service. Most homeowners spend between $131 and $454 to fix their furnace. Here is what you need to know, along with the various factors that could affect the price of your furnace repair.
Most Michigan HVAC repair companies will often charge a “Travel Charge” or “Diagnosis Fee.” Randazzo calls this fee simply, a “Service Call Fee.” This will be the minimum cost of the repair. It is not recommended to judge a company on how expensive or how cheap their service rates are. In most cases, with larger companies the rates will be higher. This is not because they may have more overhead but simply because of the quality and preparedness of the service that will be preformed.
The condensed, pressurized, and still usually somewhat hot liquid refrigerant is next routed through an expansion valve (often nothing more than a pinhole in the system's copper tubing) where it undergoes an abrupt reduction in pressure. That pressure reduction results in flash evaporation of a part of the liquid refrigerant, greatly lowering its temperature. The cold refrigerant is then routed through the evaporator. A fan blows the interior warm air (which is to be cooled) across the evaporator, causing the liquid part of the cold refrigerant mixture to evaporate as well, further lowering the temperature. The warm air is therefore cooled and is pumped by an exhaust fan/ blower into the room. To complete the refrigeration cycle, the refrigerant vapor is routed back into the compressor. In order for the process to have any efficiency, the cooling/evaporative portion of the system must be separated by some kind of physical barrier from the heating/condensing portion, and each portion must have its own fan to circulate its own "kind" of air (either the hot air or the cool air).
×