The performance of vapor compression refrigeration cycles[27] is limited by thermodynamics. These air conditioning and heat pump devices move heat rather than convert it from one form to another, so thermal efficiencies do not appropriately describe the performance of these devices. The Coefficient-of-Performance (COP) measures performance, but this dimensionless measure has not been adopted. Instead, the Energy Efficiency Ratio (EER) has traditionally been used to characterize the performance of many HVAC systems. EER is the Energy Efficiency Ratio based on a 35 °C (95 °F) outdoor temperature. To more accurately describe the performance of air conditioning equipment over a typical cooling season a modified version of the EER, the Seasonal Energy Efficiency Ratio (SEER), or in Europe the ESEER, is used. SEER ratings are based on seasonal temperature averages instead of a constant 35 °C (95 °F) outdoor temperature. The current industry minimum SEER rating is 14 SEER.[28]
The three major functions of heating, ventilation, and air conditioning are interrelated, especially with the need to provide thermal comfort and acceptable indoor air quality within reasonable installation, operation, and maintenance costs. HVAC systems can be used in both domestic and commercial environments. HVAC systems can provide ventilation, and maintain pressure relationships between spaces. The means of air delivery and removal from spaces is known as room air distribution.[3]
Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.
The burner can be fueled by gas or by oil. It is the component that creates the required heat. It can be controlled by a thermostat or by the fan limit control, which is located in the plenum chamber. A dirty air filter or a blocked fan can cause the burner to turn off and on more frequently than necessary. If you are experiencing this issue, the first thing you should try is to change the air filter. If that does not help the issue, contact UGI Heating, Cooling & Plumbing and we will send an expert technician to further troubleshoot your gas or oil furnace burner issues.
Whether it’s a sticky day in July and you need an AC repair, or your employees are having trouble breathing because of stagnant indoor air, you can rely on HI-VAC Air Conditioning Service to quickly resolve your problem. We are the go-to source for air conditioning services in Plantation, Miramar, Pembroke Pines, Weston, Coral Springs, Sunrise, FL and the surrounding area. Give us a call today to learn how we can improve your indoor comfort.
As a top provider of top-rated air conditioners and professional service, Four Seasons Heating and Air Conditioning is here to ensure that you have the cool and comfortable living environment that you deserve. Learn more about what we have to offer today by giving us a call, or request additional information now by filling out our brief online quote form!

Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
Our fully trained and certified heating technicians have been repairing installing furnaces, heating systems and heat pumps in Smyrna and the Atlanta area since 1966.  We offer 24 hour emergency service for unexpected heating system break downs.  We can provide expert maintenance and repair on your current heating system or help you select a new, high-efficiency heating system from our wide range of furnaces.
The chill of winter can be a scary thought when your furnace needs repair. When the furnace in your home goes on the fritz, you need it fixed right away to keep your family safe and comfortable. Every BGE HOME technician is licensed and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every furnace repair with the highest level of quality.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
Your HVAC professional can also help you verify that your system is properly matched by providing you with an AHRI Certificate of Certified Product Performance upon request. The certificate verifies that the outdoor unit (condenser) and the indoor unit (evaporator) combination has been certified as a matched system by the Air Conditioning, Heating and Refrigeration Institute (AHRI). For higher efficiency systems, this certification may help you obtain a rebate from your utility or local municipality if you have to replace your unit in whole or in part. Not all areas offer a rebate, but your technician will likely be able to provide information about the certification process. Fees for performing this certification vary, but generally are relatively inexpensive.
Should you need to replace an air conditioning unit, Abacus Plumbing recommends Lennox brand of air conditioning and heating systems. Lennox systems offer the highest level of home comfort at the lowest possible cost of operation. Additionally, these systems are praised by consumer publications and meet or exceed all government standards for efficiency. Learn more about installation »
The icing problem becomes much more severe with lower outdoor temperatures, so heat pumps are commonly installed in tandem with a more conventional form of heating, such as a natural gas or oil furnace, which is used instead of the heat pump during harsher winter temperatures. In this case, the heat pump is used efficiently during the milder temperatures, and the system is switched to the conventional heat source when the outdoor temperature is lower.
A programmable thermostat is a must-have in today’s state of AC technology. Programmable thermostats allow you to set temperatures for various times throughout the day and automatically lower the temperature when you most need it to help you save money and manage your cooling without constantly hovering over the dial. In this article, we’ll walk you through installing a programmable thermostat in your home.

If you live in a warmer climate, your air conditioner is likely one of the most essential pieces of equipment for your home. The best course is to perform regular routine air conditioner maintenance to ensure its smooth operation during the warmest months of the year. Annual tune-ups by a professional HVAC technician will increase the lifespan of your unit. When repairs are needed, be sure to hire a technician trained and certified in HVAC repair for best results. Following these guidelines will ensure that you are comfortable and cool through the summer season.
Allow our experts to help with any of your heating and cooling needs or questions. Our wide array of expertise and background will benefit you and your home, whether you are considering a replacement system or evaluating your whole system to check for areas of improvement. We can help you reach your optimum indoor comfort. Give us a ring at 866-397-3787 or request an appointment online.

The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.


Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.

The condensed, pressurized, and still usually somewhat hot liquid refrigerant is next routed through an expansion valve (often nothing more than a pinhole in the system's copper tubing) where it undergoes an abrupt reduction in pressure. That pressure reduction results in flash evaporation of a part of the liquid refrigerant, greatly lowering its temperature. The cold refrigerant is then routed through the evaporator. A fan blows the interior warm air (which is to be cooled) across the evaporator, causing the liquid part of the cold refrigerant mixture to evaporate as well, further lowering the temperature. The warm air is therefore cooled and is pumped by an exhaust fan/ blower into the room. To complete the refrigeration cycle, the refrigerant vapor is routed back into the compressor. In order for the process to have any efficiency, the cooling/evaporative portion of the system must be separated by some kind of physical barrier from the heating/condensing portion, and each portion must have its own fan to circulate its own "kind" of air (either the hot air or the cool air).

Handling the service needs of homeowners throughout Orlando, FL, Volusia, FL since 1910, we’ve built our business on a foundation of well-earned trust.  We uphold an A+ rating from the Better Business Bureau.  As a Carrier Factory Authorized Dealer, Ferran Services has been further distinguished with the Carrier President’s Award.  Trust that your best interest is our priority.  At Ferran Services, it’s not about the sale.  It’s all about your long-term satisfaction.


An annual inspection of your unit can ensure that the various potential problems mentioned above are detected early, and before they require complete replacement. During this inspection, for instance, a professional might find small cracks in your heat exchanger or a faulty seal in your blower motor. Some manufacturer's warranties even require these annual inspections to maintain validity. Typically, your furnace inspection will cost between $80 and $150 depending on the area in which you live and the professional you work with.
Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
We never appreciate the importance of our home’s cooling system until it starts to break down. A failing air conditioning system in need of residential AC repair has an adverse effect on our comfort, our health, and even our monthly expenses. While it might be nice to put off any AC system repairs until a later date, the longer you wait, the more likely you’ll have to pay some hefty home AC repair bills. Fortunately, with Gainesville Mechanical, Inc., we make air conditioning system repair as easy as possible. Our team of experienced technicians are trained in the latest industry advancements, and are well versed in all types of AC repair near Gainesville, GA. From commercial air conditioning repair to residential air conditioning repair, we can dispatch a service truck at a moment’s notice to take care of your emergency air conditioning repair needs. All the while performing our AC repair services in a manner of utmost courtesy and professionalism.

Has another company told you that your furnace has a cracked heat exchanger?  The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace.  Because of these issues, Bonney takes this situation very seriously.  We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.
Evaporative coolers, sometimes called "swamp coolers", do not have a compressor or condenser. Liquid water is evaporated on the cooling fins, releasing the vapor into the cooled area. Evaporating water absorbs a significant amount of heat, the latent heat of vaporisation, cooling the air. Humans and animals use the same mechanism to cool themselves by sweating.

In hot weather, air conditioning can prevent heat stroke, dehydration from excessive sweating and other problems related to hyperthermia. Heat waves are the most lethal type of weather phenomenon in developed countries. Air conditioning (including filtration, humidification, cooling and disinfection) can be used to provide a clean, safe, hypoallergenic atmosphere in hospital operating rooms and other environments where proper atmosphere is critical to patient safety and well-being. It is sometimes recommended for home use by people with allergies.


Terrible - Explained to tech that we had cold air on heat status. I placed Thermostat on emergency heat and was able to get some heat. I told him TXU had installed a a new thermostat and I think he may have installed it incorrectly but wasn't, sure. He said it would cost us more money if he fixed problem if there was one. He said I could pay for it and get reimbursed from insurance company. When he said it would cost us money I said I would live with it. I plan on calling a reputable repair company. He did not check furnace or temperature of house
Turn off the gas supply valve, typically located by your gas meter on the gas inlet pipe. Turn off the gas by rotating the valve one quarter turn with an adjustable wrench. When the gas is off,  the valve’s oblong stem points perpendicular to the inlet pipe. Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.
Whether you are in need of new installation, system replacement, seasonal maintenance, or prompt repair, M and M, Heating & Cooling, Plumbing & Electrical lives up to your highest expectations for quality, pricing, reliability, and quick turnaround on all projects.  And our commitment isn’t limited to regular business hours.  We’re always available when you need us, providing 24 hour Emergency Service across Longmont, Dacono, Frederick, Firestone, Mead, Erie & Johnstown, CO.  Trust the #1 Rated and Certified – A/C, Heating, and Plumbing Experts.
At HI-VAC Air Conditioning Service, we realize that it can be difficult to find an air conditioning company that you can trust. While many companies can handle AC repair, we strive to go above and beyond the basics. We are honest, reliable and guarantee professional 24/7 service from South Florida’s #1 Choice for air conditioning installation, service, maintenance and repair since 1970. When you choose HI-VAC Air Conditioning Service for your air conditioning and ventilation needs you’ll have our 100-percent satisfaction guarantee and first-rate service:
7) Schedule an annual tune-up with an HVAC professional. A trained HVAC technician can detect most problems before they become major ones. With a cost of around $100 for a routine maintenance call, the benefits will likely outweigh the costs by a considerable margin. A typical tune-up will include various tests to ensure your unit’s internal parts are functioning correctly, as well as a filter check, and a refrigerant charge if needed. Your technician will likely also clear the drain, and clean your unit thoroughly inside and out.
×