Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.

The blower assembly is located between your main furnace and the cold air return. The blower is responsible for pulling air from your home and then sending it through the furnace and the heat exchanger. The air gets circulated throughout the home via the duct work. The furnace’s air filter is contained within the blower compartment. Regular-style filters should be replaced or cleaned each month.


Recent Review: Had asked another company to fix furnace. Other company suggested furnace replacement to the tune of 7k. United Mech was a "second quote"; they came, they looked, they agreed the unit was older, and gave both a quote (1000 less) to replace and the suggestion that the part might be the only problem. Chose to fix not replace. Technician was clearly very familiar with repair. Second good experience with this company. First time, inquired about installing a gas stove in my house. They came, reviewed the ways to run the gas line to the kitchen. They told me it possible, explained how and then said was really too expensive to make it worth it. Unusual to have a firm talk a client out of major job. I remembered that and called them when we needed a second opinion.
The selection of indoor units has one restriction: their total power should not exceed the capacity of the outdoor unit. In practice, however, it is very common to see a multi-split system with a total capacity of indoor units greater than the outdoor capacity by at least 20%. However, it is wrong to expect better performance when all indoor units are turned on at the same time, since the total capacity of the whole system is limited by the capacity of the outdoor unit. Simply put, the outdoor unit will distribute all its power to all operating indoor units in such a way that some of the rooms may not have a very comfortable temperature level. However, the calculation of the total power is not simple, since it takes into account not only the nominal power of the units, but also the cooling capacity, heating, dehumidification, humidification, venting, etc.
Vredevoogd Heating & Cooling technicians routinely assist our customers to figure out when it’s time to upgrade their Heating or Cooling system. Naturally, repairs are part of routine maintenance over the years. However, new models can save homeowners in a big way on energy expenses with their energy-efficient makeup. When you are ready to get a new system, we will do a careful check of your energy needs so that you can select the ideal system for your home’s needs. The wrong HVAC system for your home is a 15 year mistake that no one should have to afford. We install the right system for your home. Moreover, we offer guarantees that you won’t find just anywhere else. If your new installation isn’t right for your home, we’ll remove it free of charge at any time within that first year and refund 100% of your money. Our customers are burdened with no risks. We take on the risk because we are that sure of our expertise. We back our work with the strongest warranties in the field. In fact, we offer a wide array of warranties to provide you with the peace of mind you deserve as a valued Vredevoogd Heating & Cooling Grand Rapids MI customer.
Even with the best air conditioning repair service Phoenix can offer, an AC unit that has reached the end of its shelf life must be replaced. If you are ready to upgrade or replace that aging system, call us now for a free estimate, or check out our AC Unit Replacement section. In addition to offering our own Precision Line with the best warranty available in the industry, we also partner with industry leaders to offer the highest quality equipment at the best possible price, and we personally stand behind all of our new equipment installations.
The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.

The chill of winter can be a scary thought when your furnace needs repair. When the furnace in your home goes on the fritz, you need it fixed right away to keep your family safe and comfortable. Every BGE HOME technician is licensed and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every furnace repair with the highest level of quality.
Modern Air Solutions provides the skilled and dedicated services to maintain a healthier, more comfortable indoor residential or commercial space, while saving you time and money.  Since first opening our doors in 2007, we’ve built and continue a reputation for a job well done across Aurora, Oswego, Montgomery, Bristol & Plainfield, IL. We’ve assembled a team of licensed, NATE-certified, and factory trained specialists, equipped with the leading-edge tools and technology, to quickly and accurately resolve any challenge.
Even with the best air conditioning repair service Phoenix can offer, an AC unit that has reached the end of its shelf life must be replaced. If you are ready to upgrade or replace that aging system, call us now for a free estimate, or check out our AC Unit Replacement section. In addition to offering our own Precision Line with the best warranty available in the industry, we also partner with industry leaders to offer the highest quality equipment at the best possible price, and we personally stand behind all of our new equipment installations.

If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
Maryville, TN Appliance Repair Brookfield, WI Appliance Repair Appliance Repair Santa Cruz, CA Appliance Repair Riverside Appliance Repair Naples, FL 1500 S Willow St Appliance Repairs Appliance Repair in La Crosse Appliance Repair in Laredo 200 Westgate Dr Appliance Repairs 6929 Williams Rd Appliance Repairs Appliance Repair in Chesapeake Appliance Repair in Springfield, OH Appliance Repair in Whittier Appliance Repair in Massena Appliance Repair in Duluth Appliance Repair in Richardson Appliance Repair in Saint Joseph
Your HVAC professional can perform a yearly tune-up of your system for around $80-$100. This yearly maintenance can go far toward heading off major repairs to your system and provide you with peace of mind and considerable savings in the long term. Additionally, regular servicing of your AC unit can help a home inspector to certify that your unit is working properly in the event you decide to sell your home.

Some of the things that determine air conditioning capacity in Arizona include, but are not limited to: your area’s unique climate, monsoon humidity, number of windows, their location, and their NFRC rating, ceiling and wall insulation factors, which direction your home is facing, how much heat your appliances produce, how high your ceilings are, if you have a basement, if you have proper attic ventilation, the location of trees on your property, and even the number of people who occupy the home.
The summers here in Alexandria can range from almost pleasant to downright brutal. And you know as well as we do that it’s those latter days when your central AC or heat pump will decide to go down! But you don’t have to seek solace at the Waterfront or over at Cameron Run Regional Park. The secret to restoring your comfort lies with the certified specialists at HVAC & Plumbing Unlimited!
AC air handler buzzing sounds. Do you hear a buzzing sound when you turn on the thermostat? The only thing that comes on in the house when you turn on the thermostat is the fan relay and fan in the air handler or furnace. Try switching the thermostat HEAT/COOL switch to OFF. Then switch the fan switch from AUTO to ON. The fan (only) should come on. If the air handler makes a buzzing sound, it probably has a bad fan relay or, more likely, blower fan.
Whether it’s a sticky day in July and you need an AC repair, or your employees are having trouble breathing because of stagnant indoor air, you can rely on HI-VAC Air Conditioning Service to quickly resolve your problem. We are the go-to source for air conditioning services in Plantation, Miramar, Pembroke Pines, Weston, Coral Springs, Sunrise, FL and the surrounding area. Give us a call today to learn how we can improve your indoor comfort.
Contending with South Florida’s temperature extremes is easy — if you have a heating and air conditioning contractor you can trust for prompt, dependable and affordable work. For over 40 years, our family-owned and operated company has helped home and business owners with their heating and cooling needs. From air conditioning repairs to maintaining heat pumps to installing a ductless system, you can rely on HI-VAC Air Conditioning Service. We are a full-service provider of HVAC services for Plantation, Miramar, Pembroke Pines, Weston, Coral Springs, Sunrise, FL, and the surrounding area.
According to a 2015 government survey, 87% of the homes in the United States use air conditioning and 65% of those homes have central air conditioning. Most of the homes with central air conditioning have programmable thermostats, but approximately two-thirds of the homes with central air do not use this feature to make their homes more energy efficient.[57]

It can be difficult to find the right company to do Aurora furnace repair and Aurora furnace replacement. When looking for the right help choose an Aurora furnace replacement and repair company that comes recommended and has a strong reputation. As a licensed furnace replacement company in Denver, Brothers Plumbing Heating and Electric has been working on the repair and replacement of furnaces for many years. Furthermore, we have a long list of happy customers that recommend us to all their friends and family.
If your furnace is more than 15 years old or broken beyond repair, furnace replacement is necessary. Old furnaces are very inefficient which means that you could be spending more on your gas or electric bill than you need to. Old furnaces can also be very hazardous to your health and home. Furnaces are basically controlled fires, and when the control systems on your furnace are out of date or malfunctioning, the safety of your home is in jeopardy. If you have an old or malfunctioning furnace, or if you want a safety check on your current system, then give our furnace replacement company a call today!

If you live in a warmer climate, your air conditioner is likely one of the most essential pieces of equipment for your home. The best course is to perform regular routine air conditioner maintenance to ensure its smooth operation during the warmest months of the year. Annual tune-ups by a professional HVAC technician will increase the lifespan of your unit. When repairs are needed, be sure to hire a technician trained and certified in HVAC repair for best results. Following these guidelines will ensure that you are comfortable and cool through the summer season.
1) Your air conditioner is not working at all. Before calling in a professional to address this issue, you may want to check a few things yourself. Check to see if your thermostat is set to “cool”. Confirm that your designated cooling temperature is less than the temperature of the room or home. If everything is set correctly, check the electrical panel to be sure you do not have a tripped breaker. If these things all check out and your air condition unit is still not working, it is time to call in a professional.
Shortly thereafter, the first private home to have air conditioning was built in Minneapolis in 1914, owned by Charles Gates.[11] Realizing that air conditioning would one day be a standard feature of private homes, particularly in regions with warmer climate, David St. Pierre DuBose (1898-1994) designed a network of ductwork and vents for his home Meadowmont, all disguised behind intricate and attractive Georgian-style open moldings.[when?] This building is believed to be one of the first private homes in the United States equipped for central air conditioning.[12]
The heat-exchanger cools the air that is being forced through it by the furnace blower. As the warm air comes in contact with this cool surface the water in the air condenses. By pulling the water molecules from the air. According to the psychometric chart[42] as relative humidity decreases in order to feel cool you will have to lower the temperature even more. A common way to counteract this effect is by installing a whole-home humidifier.[43] Similarly, installing a high efficient system this need to turn the temperature down wont have such and influence on your energy costs.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!
Has another company told you that your furnace has a cracked heat exchanger?  The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace.  Because of these issues, Bonney takes this situation very seriously.  We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.

Because an air conditioner moves heat between the indoor coil and the outdoor coil, both must be kept clean. This means that, in addition to replacing the air filter at the evaporator coil, it is also necessary to regularly clean the condenser coil. Failure to keep the condenser clean will eventually result in harm to the compressor, because the condenser coil is responsible for discharging both the indoor heat (as picked up by the evaporator) and the heat generated by the electric motor driving the compressor.
Your air conditioner can break down anytime, even on the unholiest of hours. That, however, is not a problem with Precision Air and Heating, since we offer 24-hour emergency service. Even if your AC conks out in the middle of an incredibly warm summer night, you won’t suffer for long if you call us ASAP. We promise to provide the best AC repair Phoenix AZ has available no matter what time you need it.
Leave gambling to the casinos! When it’s 110 degrees in the shade, you don’t want take a chance with a broken AC. Go beyond a tune-up and Rejuuuvenate! your air conditioner back to factory fresh conditions. Your AC shouldn’t sound like a slot machine, so we believe in eliminating every squeak, rattle and hum because if you don’t, bigger problems will come. So trust our highly trained, screened, and “Sadie Certified” technicians to make you the coolest act on the Strip!

If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:
Dehumidification (air drying) in an air conditioning system is provided by the evaporator. Since the evaporator operates at a temperature below the dew point, moisture in the air condenses on the evaporator coil tubes. This moisture is collected at the bottom of the evaporator in a pan and removed by piping to a central drain or onto the ground outside.
Refrigeration air conditioning equipment usually reduces the absolute humidity of the air processed by the system. The relatively cold (below the dewpoint) evaporator coil condenses water vapor from the processed air, much like an ice-cold drink will condense water on the outside of a glass. Therefore, water vapor is removed from the cooled air and the relative humidity in the room is lowered. The water is usually sent to a drain or may simply drip onto the ground outdoors. The heat is ejected by the air conditioners condenser, which is located outside of the area being cooled.
In 1995, Germany made CFC refrigerators illegal.[22] DuPont and other companies blocked the refrigerant in the U.S. with the U.S. EPA, disparaging the approach as "that German technology".[21][23] Nevertheless, in 2004, Greenpeace worked with multinational corporations like Coca-Cola and Unilever, and later Pepsico and others, to create a corporate coalition called Refrigerants Naturally!.[22][24] Then, four years later, Ben & Jerry's of Unilever and General Electric began to take steps to support production and use in the U.S.[25] In 2011 the EPA decided in favor of the ozone- and climate-safe refrigerant for U.S. manufacture.[17][26][27]
In 1820, English scientist and inventor Michael Faraday discovered that compressing and liquefying ammonia could chill air when the liquefied ammonia was allowed to evaporate. In 1842, Florida physician John Gorrie used compressor technology to create ice, which he used to cool air for his patients in his hospital in Apalachicola, Florida. He hoped to eventually use his ice-making machine to regulate the temperature of buildings. He even envisioned centralized air conditioning that could cool entire cities. Though his prototype leaked and performed irregularly, Gorrie was granted a patent in 1851 for his ice-making machine. Though his process improved the artificial production of ice, his hopes for its success vanished soon afterwards when his chief financial backer died and Gorrie did not get the money he needed to develop the machine. According to his biographer, Vivian M. Sherlock, he blamed the "Ice King", Frederic Tudor, for his failure, suspecting that Tudor had launched a smear campaign against his invention. Dr. Gorrie died impoverished in 1855, and the dream of commonplace air conditioning went away for 50 years.[citation needed]
The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
Even with the best air conditioning repair service Phoenix can offer, an AC unit that has reached the end of its shelf life must be replaced. If you are ready to upgrade or replace that aging system, call us now for a free estimate, or check out our AC Unit Replacement section. In addition to offering our own Precision Line with the best warranty available in the industry, we also partner with industry leaders to offer the highest quality equipment at the best possible price, and we personally stand behind all of our new equipment installations.
Our team of fully licensed and insured technicians each draw from between ten and thirty years of industry experience and share our unwavering dedication to customer service.  Entirely NATE-certified, our installation and service department has completed rigorous testing, and are exceptionally qualified to handle even the most complex HVAC challenges.  NATE (North American Technician Excellence) is the only nationwide certification program that is supported by the entire industry, and of all third-party certifications, has the lowest pass rate.
The blower assembly is located between your main furnace and the cold air return. The blower is responsible for pulling air from your home and then sending it through the furnace and the heat exchanger. The air gets circulated throughout the home via the duct work. The furnace’s air filter is contained within the blower compartment. Regular-style filters should be replaced or cleaned each month.
The liquid refrigerant is returned to another heat exchanger where it is allowed to evaporate, hence the heat exchanger is often called an evaporating coil or evaporator. As the liquid refrigerant evaporates it absorbs energy (heat) from the inside air, returns to the compressor, and repeats the cycle. In the process, heat is absorbed from indoors and transferred outdoors, resulting in cooling of the building.
The selection of indoor units has one restriction: their total power should not exceed the capacity of the outdoor unit. In practice, however, it is very common to see a multi-split system with a total capacity of indoor units greater than the outdoor capacity by at least 20%. However, it is wrong to expect better performance when all indoor units are turned on at the same time, since the total capacity of the whole system is limited by the capacity of the outdoor unit. Simply put, the outdoor unit will distribute all its power to all operating indoor units in such a way that some of the rooms may not have a very comfortable temperature level. However, the calculation of the total power is not simple, since it takes into account not only the nominal power of the units, but also the cooling capacity, heating, dehumidification, humidification, venting, etc.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​

In the refrigeration cycle, heat is transported from a colder location to a hotter area. As heat would naturally flow in the opposite direction, work is required to achieve this. A refrigerator is an example of such a system, as it transports the heat out of the interior and into its environment. The refrigerant is used as the medium which absorbs and removes heat from the space to be cooled and subsequently ejects that heat elsewhere.


Get an accurate price for your HVAC repair costs by contacting a local heating and cooling company and scheduling an inspection. Search HVAC.com’s Contractor Directory to find local HVAC contractors who perform heating and cooling repairs. Call for service and find the price of the HVAC repair costs needed to get your system back into good working order!
A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.
I have a very old HVAC. The heater went out. I had just purchased the heater check package from Angie's list and it went out the nex tday. I called them and John came within a day or so. He found the problem after checking several items (fuse in heater shorting). He ordered the part and there was a delay due to getting the part and then the ice storm. As soon as the part was in John texted me. When I was available, John came back in a reasonable time and fixed it. He always called half hour before he was en route to notify me and was very punctual. He is professional and knowledgeable. He used my coupon toward my total bill and I have heat! I will use him again and am thankful he could get out and get it fixed at a reasonable cost.
When your gas furnace isn’t blowing hot air, the issue could be due to a faulty pilot light or broken ignitor. Remove the furnace cover panel and visually inspect whether you can see a flame from the pilot light. A natural gas furnace will be blue and yellow in color, and a propane furnace should have a bluish green flame with a yellow tip. If you can see a flame and it appears normal, the issue could be related to the furnace blower motor or other complex furnace parts. If the flame appears low or non-existent, it’s best to contact an experienced furnace repair company. Remember to never touch any open wires; contact a professional.
A pinging or popping sound coming from the duct work can come from thermal expansion—the ductwork expanding and contracting as it heats and cools.  Or, air blowing past a loose flap of metal can make the sound. Track along the duct runs, listening for the sound. If you locate it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
HVAC repair technicians are properly qualified to take care of anything that relates to installing, maintaining or repairing your heating, air conditioning and refrigeration systems. Our professionals have gone through rigorous training and certification and all our technicians and equipment installers are NATE-certified, which involves demanding testing and indicates a solid understanding of the industry.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
Leave gambling to the casinos! When it’s 110 degrees in the shade, you don’t want take a chance with a broken AC. Go beyond a tune-up and Rejuuuvenate! your air conditioner back to factory fresh conditions. Your AC shouldn’t sound like a slot machine, so we believe in eliminating every squeak, rattle and hum because if you don’t, bigger problems will come. So trust our highly trained, screened, and “Sadie Certified” technicians to make you the coolest act on the Strip!
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
×