The Environmental Protection Agency (EPA) requires that all technicians who open a system containing a controlled refrigerant be certified to do so. There are four levels of certification, one of which is a “universal” certification to allow the HVAC technician to work on any type of equipment containing refrigerant. Your HVAC technician should be certified as “Level II Certified” at a minimum or, preferably, “Universal Certification” to work on your central air conditioner. Obtaining this certification information from your professional HVAC technician may be required in the event you are working with a realtor to sell your home. Costs for certification average $40 to $240.
The concrete pads under home air conditioner and heat exchanger units tend to settle over the years. As long as there’s no strain on the copper coolant tubes and electrical lines, and the unit stays dry and level, it’s OK that the pad has sunk. But if it continues to sink and pulls the lines tight, or if water puddles around the unit, you’ll need to take action. Here’s how to fix it.
Any concern with your cooling system, however minor, is worth checking out. NATE-certified technicians can quickly identify the problem and prevent more extensive and costly damage. Catching defects quickly is the key to cost-effective repairs. Elevated operational noise such as grinding, screeching, or wheezing is more than aggravating. Think of those sounds as warning bells. They’re an indication of component failure. Listen to what they’re telling you and call for professional assistance. Worn or misaligned belts are easily repaired. Strange smells from contaminants such as mold or mildew are best handled before allergens enter breathing air, diminish airflow, and block the coil. Temperature swings, unstable humidity, or extended run times are all signs of bigger problems on the way. Call Ferran Services at 407-422-3551 (Orlando) or 386-322-6168 (Volusia), and our licensed technicians will perform a complete system check, ensuring safe, efficient and reliable operation.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
Ground source, or geothermal, heat pumps are similar to ordinary heat pumps, but instead of transferring heat to or from outside air, they rely on the stable, even temperature of the earth to provide heating and air conditioning. Many regions experience seasonal temperature extremes, which would require large-capacity heating and cooling equipment to heat or cool buildings. For example, a conventional heat pump system used to heat a building in Montana's −70 °F (−57 °C) low temperature or cool a building in the highest temperature ever recorded in the US—134 °F (57 °C) in Death Valley, California, in 1913 would require a large amount of energy due to the extreme difference between inside and outside air temperatures. A few feet below the earth's surface, however, the ground remains at a relatively constant temperature. Utilizing this large source of relatively moderate temperature earth, a heating or cooling system's capacity can often be significantly reduced. Although ground temperatures vary according to latitude, at 6 feet (1.8 m) underground, temperatures generally only range from 45 to 75 °F (7 to 24 °C).
We contacted GatorAC and have been pleased through the entire process of the purchase, installation and the daily functioning of the unit. We spoke to Angie to get information about the Trane AC. She arranged for Carlos Garcia to come to the house to determine the unit that would fit our needs. We made the choice between 3 units on Thursday and the unit was installed Friday. The Installation team, Willie Shaw and Gary Barber were the best. When they left everything was done, clean and clear and working great. We would recommend GatorAC for your AC needs.
We are so happy with the service and the unit installed. Carlos, the sales representative, was very attentive to our needs at the time. He knew exactly what we needed for our a/c concerns. Brandon Hayword, the a/c installer was amazing. I have never seen a technician so meticulous. Every detail was attended to. Poor guy worked from morning till 4:00 Am the next day. Never heard a complaint or wanted to go home and call it a night. Again, thank-you for the great service.
I have a very old HVAC. The heater went out. I had just purchased the heater check package from Angie's list and it went out the nex tday. I called them and John came within a day or so. He found the problem after checking several items (fuse in heater shorting). He ordered the part and there was a delay due to getting the part and then the ice storm. As soon as the part was in John texted me. When I was available, John came back in a reasonable time and fixed it. He always called half hour before he was en route to notify me and was very punctual. He is professional and knowledgeable. He used my coupon toward my total bill and I have heat! I will use him again and am thankful he could get out and get it fixed at a reasonable cost.