Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.
This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Read More Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state. Read Less Aire Serv is a registered trademark of Aire Serv LLC © Aire Serv | All rights reserved | All Aire Serv franchise locations are independently owned and operated.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
At HI-VAC Air Conditioning Service, we realize that it can be difficult to find an air conditioning company that you can trust. While many companies can handle AC repair, we strive to go above and beyond the basics. We are honest, reliable and guarantee professional 24/7 service from South Florida’s #1 Choice for air conditioning installation, service, maintenance and repair since 1970. When you choose HI-VAC Air Conditioning Service for your air conditioning and ventilation needs you’ll have our 100-percent satisfaction guarantee and first-rate service:
The chill of winter can be a scary thought when your furnace needs repair. When the furnace in your home goes on the fritz, you need it fixed right away to keep your family safe and comfortable. Every BGE HOME technician is licensed and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every furnace repair with the highest level of quality.
Talk to your HVAC repair contractor about options to make HVAC repair costs more affordable. Many contractors offer financing options to assist customers in this very position, as well as payment plans. HVAC companies know HVAC repair costs can come as quite a shock in some scenarios, and want to help you get the repairs your system needs to preserve your comfort and safety.
Summer in Orlando, FL, Volusia, FL is a brutal combination of high temperatures and humidity.  The only possible way to find relief is through a well-functioning cooling system.  Running your air conditioner day in and day out puts a great deal of stress on the equipment and can add up to high utility bills.  You need your cooling system running in peak condition to ensure maximum reliability and efficiency.  When you notice any disruption in performance, don’t wait for complete system failure.  Call the dedicated team from Ferran Services for prompt, economical, and lasting solutions.
The selection of indoor units has one restriction: their total power should not exceed the capacity of the outdoor unit. In practice, however, it is very common to see a multi-split system with a total capacity of indoor units greater than the outdoor capacity by at least 20%. However, it is wrong to expect better performance when all indoor units are turned on at the same time, since the total capacity of the whole system is limited by the capacity of the outdoor unit. Simply put, the outdoor unit will distribute all its power to all operating indoor units in such a way that some of the rooms may not have a very comfortable temperature level. However, the calculation of the total power is not simple, since it takes into account not only the nominal power of the units, but also the cooling capacity, heating, dehumidification, humidification, venting, etc.
Engineers have pointed out some areas where efficiency of the existing hardware could be improved. For example, the fan blades used to move the air are usually stamped from sheet metal, an economical method of manufacture, but as a result they are not aerodynamically efficient. A well-designed blade could reduce electrical power required to move the air by a third.[29]
"Very impressed. Returned call within 24 hours. They came out the same day I spoke with them and made the repair within 25 minutes. Very low service call fee. I had another repair service out two weeks earlier and after 3 service calls and the central air still not fixed and temperatures in the high 90's, it was such a relief to have a company identify the problem, have the necessary part with them and fix the problem."

Vredevoogd Heating & Cooling stands behind its services and products with the strongest guarantees you’ll find anywhere. When you invite us into your home to service or install your HVAC system or do Furnace Repair work in Grand Rapids and beyond, we perform our job with an outstanding level of care and efficiency. Having served Michigan for 54 years, we never rest on our laurels. To remain the best, we intend to give our best every time, every job.
American design standards are legislated in the Uniform Mechanical Code or International Mechanical Code. In certain states, counties, or cities, either of these codes may be adopted and amended via various legislative processes. These codes are updated and published by the International Association of Plumbing and Mechanical Officials (IAPMO) or the International Code Council (ICC) respectively, on a 3-year code development cycle. Typically, local building permit departments are charged with enforcement of these standards on private and certain public properties.
At times, malfunctions strike without warning.  These problems rarely stick to regular business hours.  When your comfort, safety, and well-being is at stake, don’t wait for Monday morning.  The service team from Ferran Services is available 24/7 to provide the prompt and dependable assistance you require.  Fully-stocked service trucks and extensively trained technicians allow us to handle the majority of repair requirements in a single visit.  We work on all makes and models, and our technicians do not rely on commission.  We never take advantage of your desperate situation, never sell you a product or service you don’t need, and always keep you informed.  By relying on Factory Authorized Parts, we restore system efficiency, sound levels, and longevity.
In the most general sense, air conditioning can refer to any form of technology that modifies the condition of air (heating, (de-) humidification, cooling, cleaning, ventilation, or air movement). In common usage, though, "air conditioning" refers to systems which cool air. In construction, a complete system of heating, ventilation, and air conditioning is referred to as HVAC.[3]
Gas furnaces and heaters have control shutoffs to prevent gas leaks, but they are not fail-safe. If you smell gas in your house, do not turn any lights on or off, and do not try to shut off the gas leading to the furnace. Get out of the house, leaving the door open, and immediately call the gas company or the fire department to report a leak. Do not re-enter your home.
Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5). 
×