Consequently, this water must exit the air handler—typically through plastic pipe or a drain tube. That drain tube goes directly outside, often terminating near the compressor, or to a floor drain or to a small electric “condensate pump” located by the air handler. Where a condensate pump is used, it connects to a 1/2-inch vinyl or rubber tube that exits outdoors or to a drain.

The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.
Any concern with your cooling system, however minor, is worth checking out.  NATE-certified technicians can quickly identify the problem and prevent more extensive and costly damage.  Catching defects quickly is the key to cost-effective repairs.  Elevated operational noise such as grinding, screeching, or wheezing is more than aggravating.  Think of those sounds as warning bells.  They’re an indication of component failure.  Listen to what they’re telling you and call for professional assistance.  Worn or misaligned belts are easily repaired.  Strange smells from contaminants such as mold or mildew are best handled before allergens enter breathing air, diminish airflow, and block the coil.  Temperature swings, unstable humidity, or extended run times are all signs of bigger problems on the way.  Call Ferran Services at 407-422-3551 (Orlando) or 386-322-6168 (Volusia), and our licensed technicians will perform a complete system check, ensuring safe, efficient and reliable operation.
The condensed, pressurized, and still usually somewhat hot liquid refrigerant is next routed through an expansion valve (often nothing more than a pinhole in the system's copper tubing) where it undergoes an abrupt reduction in pressure. That pressure reduction results in flash evaporation of a part of the liquid refrigerant, greatly lowering its temperature. The cold refrigerant is then routed through the evaporator. A fan blows the interior warm air (which is to be cooled) across the evaporator, causing the liquid part of the cold refrigerant mixture to evaporate as well, further lowering the temperature. The warm air is therefore cooled and is pumped by an exhaust fan/ blower into the room. To complete the refrigeration cycle, the refrigerant vapor is routed back into the compressor. In order for the process to have any efficiency, the cooling/evaporative portion of the system must be separated by some kind of physical barrier from the heating/condensing portion, and each portion must have its own fan to circulate its own "kind" of air (either the hot air or the cool air).
Central, "all-air" air-conditioning systems (or package systems) with a combined outdoor condenser/evaporator unit are often installed in North American residences, offices, and public buildings, but are difficult to retrofit (install in a building that was not designed to receive it) because of the bulky air ducts required. (Minisplit ductless systems are used in these situations.) Outside of North America, packaged systems are only used in limited applications involving large indoor space such as stadiums, theatres or exhibition halls.
I have a very old HVAC. The heater went out. I had just purchased the heater check package from Angie's list and it went out the nex tday. I called them and John came within a day or so. He found the problem after checking several items (fuse in heater shorting). He ordered the part and there was a delay due to getting the part and then the ice storm. As soon as the part was in John texted me. When I was available, John came back in a reasonable time and fixed it. He always called half hour before he was en route to notify me and was very punctual. He is professional and knowledgeable. He used my coupon toward my total bill and I have heat! I will use him again and am thankful he could get out and get it fixed at a reasonable cost.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.

If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
R22 (also known as HCFC-22) has a global warming potential about 1,800 times higher than CO2.[62] It was phased out for use in new equipment by 2010, and is to be completely discontinued by 2020. Although these gasses can be recycled when air conditioning units are disposed of, uncontrolled dumping and leaking can release gas directly into the atmosphere.
To be honest, an HVAC technician’s work goes beyond more than installation, maintenance and repair. Most people are increasingly spending more time inside the home, so indoor air quality, home energy savings and total comfort have become even more important. There are several choices and solutions when it comes to HVAC systems, and our experts will consult with you every step of the way and work with you to achieve your goals.
The most recognized standards for HVAC design are based on ASHRAE data. The most general of four volumes of the ASHRAE Handbook is Fundamentals; it includes heating and cooling calculations. Each volume of the ASHRAE Handbook is updated every four years. The design professional must consult ASHRAE data for the standards of design and care as the typical building codes provide little to no information on HVAC design practices; codes such as the UMC and IMC do include much detail on installation requirements, however. Other useful reference materials include items from SMACNA, ACGIH, and technical trade journals.
In the event of an emergency with your residential heating and cooling system, we understand that you simply cannot wait! At R.S. Andrews, we take your comfort and well-being seriously and are proud to offer our emergency HVAC repair at any hour, on any day—including weekends! We provide only the highest quality services to ensure your needs are met!
We want to compliment your fine sales and installation team. They are outstanding. Carlos, your sales rep., was highly informative. We reviewed our needs and we ultimately chose the Trane XV-18 variable speed system. Carlos did not try to up sell us with things that we did not need but he did help us choose the correct upgraded filter and UV light that we wanted. We told Carlos that our research indicated that the quality of the installation of the unit was at least as important as the unit itself, and Carlos agreed. Carlos pointed out that new proper sized duct work and copper wiring would be required for a correct installation, and that we needed to add two more returns. We asked if more returns were needed and Carlos said that would not be cost effective. That was great to hear. Carlos assured us that the installation team of Willie and Gary, both lead installers, would be used. They were both superb. They came on time and worked for 12 and 1/2 hours. It was a 93 degree day so the heat in the attic was intense. We kept telling them to take a break but they continued to work up there in what must have been 130+ temperatures. They were amazing! They were neat and cleaned up any mess they made. They patiently answered all of our many questions and gave us helpful tips. They were truly professional in all respects. We also note that Stacy, Angie and Karen of your office staff were each courteous, accommodating and efficient. They helped things to go smoothly. Carlos, Gary, Stacy, Angie, Willie and Karen are each great assets to your company. We would be comfortable recommending that team of people to anyone! Ken and Kathy Luban
It can be difficult to find the right company to do Aurora furnace repair and Aurora furnace replacement. When looking for the right help choose an Aurora furnace replacement and repair company that comes recommended and has a strong reputation. As a licensed furnace replacement company in Denver, Brothers Plumbing Heating and Electric has been working on the repair and replacement of furnaces for many years. Furthermore, we have a long list of happy customers that recommend us to all their friends and family.
During the colder months of the year, the comfort of your home depends on the proper working function of your heating system. When your furnace breaks down or stops working properly, reach out to the heating experts at Horizon Services! We have nearly 30 years of experience providing reliable furnace repairs for homeowners throughout Delaware, Southern New Jersey, Southeastern Pennsylvania, and Northeastern Maryland. Our technicians are able to repair just about any type of home furnace using cutting-edge techniques and state-of-the-art tools. We can accurately diagnose the root of the issue and quickly get to work making the necessary repairs. We even offer same day service at no additional cost!
A lot of heat enters the home through windows, especially open windows. If you really want to control heat in your house, pay attention to your windows, too. Keep them closed and covered with blinds or drapes during the hottest parts of the day—especially windows that are currently facing the sun. Here are more tips for cutting cooling costs this season.

About us: Vredevoogd Heating & Cooling has been in business since 1964. As a financially stable company known for its reliable expertise and first-rate customer care, Vredevoogd Heating & Cooling is a company you can trust. Moreover, when you do business with a stable business like Vredevoogd Heating & Cooling, you have the peace of mind of knowing that your warranties are solidly backed by a company that intends to remain in business for another 50+ years and beyond. Don’t trust your essential home systems and investment to any fly-by-night company. Our best practices ensure that we will be here to meet our customer’s HVAC needs for decades to come. Vredevoogd Heating & Cooling founder Dennis Vredevoogd set the high standards by which the company continues to pride itself for. Today, the company continues to be family owned and operated by the founder’s sons, Michael and Thomas, who are committed to maintaining the company’s high standards and complementing them with the innovative technical know-how needed to service today’s advanced HVAC systems.

When your home or workplace is too hot or too cold, no one is happy. We have the expertise to solve any temperature problems you may have. We also realize that temperature isn’t the only factor in comfort: ventilation, indoor air quality, and automation also play a role in making your indoor environment a haven for your family, customers and employees.


A contactor is a $25 mechanical relay that uses low-voltage power from the thermostat to switch 220-volt high-amperage current to the compressor and condenser fan. AC contactors can wear out and are at the top of the list of common air conditioning service failures. Even if your contactor is working, it pays to replace it every five years or so. Unscrew the old contactor before removing the wires. Then move the wires to the new unit (photo 6).
Air conditioners can create a lot of water because they remove moisture from the air. To get rid of this, they have a [usually plastic] drain pipe that comes out of the side of the air handler. Over time, algae can block this pipe and, when it does, the AC won’t work. In fact, some condensate drains have a float switch that won’t let the AC run if water backs-up. Water can also puddle around the unit or flood the area. To deal with condensate problems, please see Air Conditioner Leaks Water, below.
Air Conditioning Your home's air conditioner is an essential part of your overall indoor comfort. A properly working system can mean the difference between a cool, comfortable summer and a hot, miserable few months. If you're currently dealing with a broken air conditioner, an inefficient system, or you would like to schedule a routine, pre-season tune-up, Horizon Services is here to help!

Recent Review: Metro Service was amazing. They came out on Saturday and secured the gas to a failing furnace to insure our safety. They came out on Monday and had the new furnace installed and operating within less than 4 hours. Polite, professional, meticulous and 35% lower than their competitors. I will be using them for all of my HVAC needs in the future.
Ventilation is the process of changing or replacing air in any space to control temperature or remove any combination of moisture, odors, smoke, heat, dust, airborne bacteria, or carbon dioxide, and to replenish oxygen. Ventilation includes both the exchange of air with the outside as well as circulation of air within the building. It is one of the most important factors for maintaining acceptable indoor air quality in buildings. Methods for ventilating a building may be divided into mechanical/forced and natural types.[16]
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
Inside the unit, the air passes over the evaporator coil first, and is cooled and dehumidified. The now dehumidified, cold air then passes over the condenser coil where it is warmed up again. Then the air is released back into the room. The unit produces warm, dehumidified air and can usually be placed freely in the environment (room) that is to be conditioned.
Whole-house fans have helped cool homes for a century. The basic design is simple: An attic-mounted fan pushes hot air out through attic vents and draws cooler, outside air in through open doors and windows. This rapid air exchange—large fans can purge a house of hot air in two to three minutes—not only removes built-up heat but also creates a pleasant breeze.
In 1758, Benjamin Franklin and John Hadley, a chemistry professor at Cambridge University, conducted an experiment to explore the principle of evaporation as a means to rapidly cool an object. Franklin and Hadley confirmed that evaporation of highly volatile liquids (such as alcohol and ether) could be used to drive down the temperature of an object past the freezing point of water. They conducted their experiment with the bulb of a mercury thermometer as their object and with a bellows used to speed up the evaporation. They lowered the temperature of the thermometer bulb down to −14 °C (7 °F) while the ambient temperature was 18 °C (64 °F). Franklin noted that, soon after they passed the freezing point of water 0 °C (32 °F), a thin film of ice formed on the surface of the thermometer's bulb and that the ice mass was about 6 mm (1⁄4 in) thick when they stopped the experiment upon reaching −14 °C (7 °F). Franklin concluded: "From this experiment one may see the possibility of freezing a man to death on a warm summer's day."[9]
×